Magnolia Plastics Magnobond 36

Plastics for the Space Age Since 1957


Magnobond 36, Parts A & B

DESCRIPTION

Magnolia 36, A & B is an unimmulsifiable, two component, 100% solids, low viscosity, epoxy adhesive and coating compound that will cure in fresh or salt water.

SPECIAL FEATURES

Magnobond 36 is:

(1) Approved by the Florida Department of Transportation per Specification Section 406 for underwater bridge piling and dock repair.

(2) The low viscosity and long pot life of Magnobond 36 makes it an excellent pressure injection grout above or below water.

(3) Magnobond 36 can be mixed with clean, dry sized sand up to 3 parts of sand to 1 part of epoxy mix by volume.


TYPICAL PHYSICAL PROPERTIES
Mix Ratio1:1 by volume
Color36A is a straw colored, 36B is amber; OR 36A is white and 36B is black to meet Federal Color Standard 559, Table VIII, Shade 36622
Viscosity36A is 500 cps; 36B is 9000 cps; 36 Mix is 1400 cps
Shelf LifeOne year unmixed and closed
Pot Life3 ounce is 4 to 5 hours @ 77°F; 1/2 gallon is 55 minutes @ 77°F
Final Cure7 days @ 77°F
Tensile Strength, psi, ASTM D 6382500
Tensile Elongation, %, ASTM D 63820
Compressive Strength, psi, ASTM D 6956000
Compressive Modulus, psi, ASTM D 69585,000
Water Absorbtion, %, ASTM D 5700.1
Specific Gravity36A is 1.14; 36B is 1.12; 36 Mix is 1.13


COVERAGE

Magnolia 36 is a 100% solids system and will give a coveage of 1,600 ft. per gallon per mil of application; i.e., 300 ft. per gallon of 5 mils, 50 ft per gallon at 1/32", and 25 ft. per gallon at 1/16".

APPLICATION

Preparation of Substrate. Surfaces to be bonded or coated should be clean and free of dirt, oil, and other foreign matter. Sandblasting, wire brushing or water and sandblasting is recommended for optimum adhesion. The surfaces need not be dry and may be underwater.

Mixing. Thoroughly mix 1 part by volume of 36A with 1 part by volume of 36B for at least 2 minutes. Do not mix more material than be used in 2 to 3 hours.

Application. Magnobond 36 may be applied with a brush, roller, or squeegee. When Magnobond 36 is made into a mortar by the addition of sand, it may be applied by a trowel, spatula, or caulking gun.

Handling. Magnobond 36 has been formulated with epoxy chemicals and hardeners. Care should be taken to prevent contact with the skin for any length of time. In the event of skin contact, wash immediately with soap and water. In the event of contact with eyes, flush with water immediately and see a physician. Uncured Magnobond 36 may be removed from tools with soap and water or with toluene. 




            DANGER                            FIRST-AID
--------------------------------     -------------------------
May cause severe irritation.         Eyes - Immediately flush
Do not get in eyes, on skin          eyes with plenty of water
or clothing.                         for at least 15 minutes.
Do not inhale vapors.                Get medical attention.
Wear rubber gloves & aprons.         Skin - Wash immediately
Use with adequate ventilation.       with soap and water.
Wash thoroughly after handling.      Clothing - Remove clothing
For industrial use only.             and wash before reuse.
Keep container closed.
Do not reuse this container.
Spec Sheet Dated: 07/31/85

For more information, contact us at:

How To Order:

Doing Business with Magnolia Plastics



Return to Magnolia Plastics Home Page

Copyright © 1996, Magnolia Plastics, Inc. All Rights Reserved, including the right of reproduction in whole or in part in any form. The stylized Magnolia Plastics logo is a regsitered trademark of Magnolia Plastics, Inc.

Contact Magnolia at sales@magnapoxy.com
Web Page Construction and Maintenance By: IFDS Enterprises, Inc.
Updated: September 26, 1996