Magnolia Plastics Adhesive Magnobond 6175-NM
Plastics for the Space Age Since 1957
Magnobond 6175-NM (Single Component)
DESCRIPTION
Magnobond 6175-NM is a non metallic filled single component epoxy adhesive
system designed for those applications requiring high bond strength and/or
electrical insulation.
SPECIAL FEATURES
1. Magnobond 6175-NM does not contain asbestos fibers or 4'4 methylene
dianiline.
2. Magnobond 6175-NM meets the requirements of BMS 11309D and MIS
13984.
3. Magnobond 6175-NM has high adhesive strength over a broad range of
temperatures and bond line thicknesses.
4. Cure temperatures as low as 120°C and times as short as 45 minutes
give good results.
PROPERTIES
| Specific Gravity: | 1.30 | | |
| Viscosity @ 25°C: | 940,000 CPS | | |
| Gel Time, 2 grams @ 125°C: | 4 Minutes | | |
| Cure Schedule: | 45 - 60 Minutes @ 125°C | | |
| Shelf Life: | 1 Month @ 25°C; 6 Months, 5°C | | |
| SPI Classification: | 4 | | |
| Flash Point: | >100°C | | |
| Freight Class: | 1 | | |
CURED PROPERTIES
Hardness, Shore D, ASTM D 2240 at 125°C: 67
Tensile Lap Shear Strength, psi, ASTM D-1002
25°C, .004" Glue Line: 5400
25°C, .010" Glue Line: 5255
82°C, .004" Glue Line: 5270
82°C, .010" Glue Line: 5025
Fatigue Strength, cycles, ASTM D 3166
modified by MMM A 132A, at 750 psi
stress: >1.6 x 106
Creep Rupture, deformation, MMM-A-132A,
1600 psi load, 192 hours at 25°C: 0.0045 in.
Creep Rupture, deformation, MMM-A-132A,
1600 psi load, 192 hours at 82°C: 0.0066 in.
Water Resistance, Lap Shear Strength after
water soak at 75°F, ASTM D-1002,
Aluminum to Aluminum:
Days in Water PSI
------------- ---------
0 5400
30 4700
60 4500
120 4300
488 4300
730 4300
2300 3690
Water Absorption, Weight Gain - Cure 1 hour @ 125°C
% gain after 4 hours in 75°F water - .2257% avg
% gain after 6 hours in 75°F water - .3298% avg
% gain after 24 hours in 75°F water - .4939% avg
% gain after 4 days in 75°F water - 1.0787% avg
% gain after 6 days in 75°F water - 1.3201% avg
% gain after 7 days in 75°F water - 1.3201% avg
Cure 1 hour @ 125°C
Thermal Conductivity
2.42 X 10-4 cal cm/sec cm2 °C
5.12 X 10-2 btu ft/hr ft 2 °F
Tensile Elongation
1.08%
Tensile Modulus
414,139 psi
DANGER FIRST-AID
-------------------------------- -------------------------
May cause severe irritation. Eyes - Immediately flush
Do not get in eyes, on skin eyes with plenty of water
or clothing. for at least 15 minutes.
Do not inhale vapors. Get medical attention.
Wear rubber gloves & aprons. Skin - Wash immediately
Use with adequate ventilation. with soap and water.
Wash thoroughly after handling. Clothing - Remove clothing
For industrial use only. and wash before reuse.
Keep container closed.
Do not reuse this container.
Spec Sheet Dated: 04/10/95
For more information, contact us at:
Sales Division
Magnolia Plastics, Inc.
5547 Peachtree Industrial Boulevard
Chamblee, GA 30341-2296 USA
770-451-2777, Voice
770-451-5376, FAX
800-831-8031, Voice
Email: sales@magnapoxy.com
How To Order:
Doing Business with Magnolia Plastics
Return to Magnolia Plastics Home Page
Copyright © 1996, Magnolia Plastics, Inc. All Rights Reserved, including
the right of reproduction in whole or in part in any form. The stylized Magnolia Plastics logo is a
regsitered trademark of Magnolia Plastics, Inc.
Contact Magnolia at sales@magnapoxy.com
Updated: September 26, 1996
